Teltonika FMC001 Setup

Teltonika FMC001 Setup

FMC001 First Start

FMC001 First Start
Qsg rut950 teltonika.PNG



ACTIVE FLEET RECOMMEND THE QUICK SMS CONFIGURATION


Advanced Plug and Track real-time tracking terminal with GNSS, GSM and Bluetooth connectivity

FMC001 4000X4000 1.png




How to insert Micro-SIM card and connect battery

  1. Gently remove FMC001 cover using plastic pry tool from both sides.
  2. Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
  3. Connect battery as shown to device. Position the battery in place where it does not obstruct other components.
  4. Attach device cover back.

Device is ready to be connected.

Fmm001 cover 1.pngFmm0001 cover 2.pngFmm001 battery 1.pngFmm001 cover 3.png


Alert.png
Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and battery are disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.

Pinout

PIN NUMBERPIN NAMEDESCRIPTION
OBD data 10-30V pinout.jpg
2PWM_BUS+/VPW
4GND (-)Ground.
5GND (-)Ground.
6CAN_HCAN high.
7K-Line
10PWM_BUS-
14CAN_LCAN low.
15L-Line
16VCC (10-30)V DC (+)Power supply (+10..+30 V DC).

PC Connection (Windows)

  1. Power-up FMC001 with DC voltage 10-30 V power supply using supplied power cable. LED’s should start blinking, see “FMC001 LED status”.
  2. Connect device to computer using Micro-USB cable or Bluetooth connection:
    • Using Micro-USB cable
      • You will need to install USB drivers, see "How to install USB drivers (Windows)"
    • Using Bluetooth
      • FMC001 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMC001_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
  3. You are now ready to use the device on your computer.

How to install USB drivers (Windows)

  1. Please download COM port drivers from Teltonika.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first FMC001 device will have default factory settings set. These settings should be changed according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Get the latest FMC001 Configurator version. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements
Operating systemMS .NET Framework versionVersionLink
  • Windows Vista
  • Windows 7
  • Windows 8.1
  • Windows 10
MS .NET Framework 4.6.232 and 64 bitwww.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking Language icon.png in the right bottom corner:

FMB Configurator language.jpg

Configuration process begins by pressing on connected device:

Configurator connect-FMC001.png

After connection to Configurator Status window will be displayed:

FMC001 Beacon-info-FMB0 series.png

Various Status window tabs display information about GNSSGSMI/OMaintenance and etc. FMC001 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

  1. Load from device.png Load from device – loads configuration from device.
  2. Save to device.png Save to device – saves configuration to device.
  3. Load from file.png Load from file – loads configuration from file.
  4. Save to file.png Save to file – saves configuration to file.
  5. Firmware update.png Update firmware – updates firmware on device.
  6. Read records.png Read records – read records from device.
  7. Reboot device.png Reboot device – restarts device.
  8. Reset configuration.png Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

"  setparam 2001:telstra.internet;2002:;2003:;2004:217.23.132.215;2005:47776;2006:1"

GPRS settings:

  • 2001 – APN (telstra.internet)
  • 2002 – APN username (if there are no APN username, empty field should be left)
  • 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

  • 2004 – Domain (217.23.132.215)
  • 2005 – Port (47776)
  • 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Note: Before SMS text, two space symbols should be inserted.

IOS sms cfg.png
Default configuration settings
Movement and ignition detection:
Accelerometer.pngVehicle movement will be detected by accelerometerIgnition detection-2-2.pngIgnition will be detected by vehicle power voltage between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:
300s icon 2.png300 seconds passesAngle 10 2.pngVehicle turns 10° degrees
Min distance.pngVehicle drives 100 metersSpeed delta.pngSpeed difference between last coordinate and current position is greater than 10 km/h
Device makes a record On Stop if:
1h icon.png1 hour passes while vehicle is stationary and ignition is off
Records sending to server:
120 s.pngIf device has made a record it is sent to the server every 120 seconds


After successful SMS configuration, FMC001 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.




Safety information

This message contains information on how to operate FMC001 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

  • The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30V DC.
  • To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
  • Before unmounting the device from the vehicle, ignition MUST be OFF.






Precautions

Bw nb.pngDo not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
Bw nb.pngAll wireless data transferring devices produce interference that may affect other devices which are placed nearby.
Bw key.pngPlease consult representatives of your vehicle model regarding OBD II location on your vehicle. In case you are not sure about proper connection, please consult qualified personnel.
Bw tick.pngThe programming must be performed using a PC with autonomic power supply.
Bw humidity.pngThe device is susceptible to water and humidity.
Bw ecute.pngInstallation and/or handling during a lightning storm is prohibited.
Bw nb.pngTeltonika is not responsible for any harm caused by wrong cables used for connection between PC and FMC001.
Bw nb.pngWARNING! Do not use FMC001 device if it distracts driver or causes inconvenience due to OBD II placement. Device must not interfere with driver.

https://teltonika-gps.com/product/fmc001/